This case is a bit cheaper than Magna Sliders from Battlefoam. The other advantages that it has over Magna Racks is that you can configure the shelf height on the fly, and your models are kept fully encased (dust protection!). This is the kind of magnetic storage solution I have been waiting for.The covered cake trays I have been using are objectively cheaper than this solution, but they take up much more space and do not fit all models (they have a set height). They also do not fit an entire 40k army in one tray, nor are they stackable.The plastic this is made from looks nice and sturdy. It's not too light weight though, so the build case has a bit of heft to it. Not nearly as much as one build entirely of wood, though, I'd imagine.The trays themselves are thin and feel very light weight, but I consider that an advantage. Magnetically, they do the job better than covered cake baking trays. I am not worried about my models sliding around or getting loose.The connections for the screws in top and bottom look up to the job, but over-tightening will definitely cause them to be ripped out of the plastic. Use common sense and you'll be fine. You can tighten the screws, and you will feel when they are secure. That's where you stop. I don't worry for a second that the screws will rip out of the plastic in normal daily use, not even with much more weight in the case than I have in it.The door is held closed by friction. This seems like a bad idea, until you actually feel the closure, and then you realize it's just fine. This was the biggest thing holding me back from ordering (you know, in the hemming and hahing phase) but it turned out to be a total non-issue for me.What would have made this case better?1. I would have liked something to secure the door. Nothing a strap won't fix, but that would've been nice. However, Jucoci has a bag on the way, supposedly, that fits this case. That totally resolves this issue, I suspect, as it really only is a concern in transport (and really probably not even then...)2. I would've like to be able to put a carry strap on. Again: the promised bag will likely take care of this.3. It would've been a great idea if this was made to securely stack. These cases do stack, as the handle folds down in an indentation in the top, but there is no feature that would prevent the top box from sliding off. I think that's a bit of an oversight in the design. They should have made some bumps on the bottom, and matching divets on the top, to prevent the cases from sliding around when stacked on top of each other (or some similar solution).All in all, I highly recommend this case. The issues listed above are nitpicky at best. I think this is the best magnetic storage on the market right now, and also one of the cheapest (if still NOT cheap!)

Assembly was easy and straightforward. Quality feels good and is sturdy once all the pieces are together.The trays on mine came a little warped? Not sure what happened but they just have a little wiggle in the slots. They don't appear to be at risk of falling out.Door seems to close fairly securely as well. This is more than 2k points of Imperial Knights and it seems tall enough to stack two big knights on top of each other.Currently I have 6 Armigers and 3 Questoris/Dominus class in the case currently and I am confident it would fit much more.Bottom Line: I would 100 percent recommend this case. The value proposition is off the charts for this one.

I'm coming from Tabletop Stronghold, who makes a very good case with some deficiencies that annoyed me a bit (MDF material scratches table surfaces, not a great door solution, handle sticking out on top, sharp corners, etc.) This case addresses literally all the little issues I had with my previous one.This case is in the same style, that is, a slide-out magnetic tray system, which IMO is ideal and the absolute best way to transport miniatures. You can easily leave as much or as little space as you need between the trays and don't have to decide beforehand like you would with something like MagnaRacks.Usable interior space is plentiful and basically identical to the TT Stronghold case I'm using as my basis of comparison. The trays hold virtually the same number of models and the cookie tray design helps prevent parts of your models from scraping against the interior walls. It has an actual hinged front door that opens to the side. The handle folds down so you can sit stuff on top of it.Now, the downside of this case is that it's a bit bulkier on the outside. Personally, this doesn't bother me because making it smaller would involve using much more expensive materials. It's plenty solid as-is and I'm quite happy not paying multiple hundreds of bucks for a miniature transport solution.